How to Build a Car Mount for Your Cellphone from Office Supplies
Reader Ryan Mottau built this awesome DIY smartphone car mount using our favorite DIY wonder-tool, the binder clip. Here's how he did it.
Problem: I wanted to take full advantage of the mapping and other car-friendly features on my Android phone without having to look down or have the phone slide under off my leg and under my foot, especially when traveling in rental cars.
Idea: Inexpensive mounting system (so that if I lose it I am not out a $45 accessory) that can attach to any car and provide close to line-of-sight use of my phone.
Solution: Modified extra large binder clip with some reverse tension (from rubber bands) and protective covering.
Step 1: Modify Your Binder Clip
Disassemble clips and bend ends of each wire piece using two sets of pliers to the angle shown in pictures below.
Step 2: Wrap the Wire for Protection
To protect my phone from scratching and provide some friction to hold phone in place, I tie off black thread on one side and wrapped around the bent wire until it provides a tight covering.
A few more times around both sides of the wire helps hold the whole thing together. Then reassemble the binder clip with the round ends bending in toward each other, wrap remaining exposed wire with duct tape (I found that I could put a width of duct tape into the "mouth" of the clip and then pull it over the exposed wire, clipping the tape to fit I then wrapped the excess around the back of the wire holding the thread in place and providing a clean, all-black exterior).
Step 3: Add Rubber Bands for Reverse Tension
In this step, you want to wrap rubber bands around the wire holders to provide the reverse tension necessary to hold your phone in place. Rubber band wrapping will depend on the size and strength of the band, I doubled my band up and then went once more around one side of the clip.The Final Final Product:
The genius of this design is that it provides a double clip, one side to attach to the car (fits onto vent louvers) and the other side holds phone securely in landscape orientation.
I have tested this in several rental cars, my own Mazda 3, and with a variety of different phones (my Droid X shown, also tried with EVO 4G, Droid 1/2, iPhone 4). The clip will generally hold a big phone like the X or an EVO in either landscape or portrait orientation with or without a case. Smaller slicker phones like the iPhone 4 will work but hold better with a case. Orientation is dictated more by the car's vents (or other securing point) but in the case of the Droid X, the side mounted power cord makes landscape the better way to attach anyway. iPhone 4 suffers disadvantage in that portrait mode is less secure and the power cord pulling down makes slipping out more likely. A rubberized case helps with grip.
Bonus: It Doubles as a Stand
The clip can also be used as a stand but this is not as elegant as clipping it on to something.
I see no way to produce these that won't take more time than I could possibly charge for them, so I figured I will just put it out there and let people build, improve and enjoy.
Want to browse some other DIY car mount alternatives before you commit to one build? We've got 'em:
');
Your version of Internet Explorer is not supported. Please upgrade to the most recent version in order to view comments.Is it the best idea to attach that to a heat vent? Replyenvador promoted this commentshaneawatson approved this comment
Reply
Hello Ladies. Look at your man's phone mount, now look at mine, now look at his, now back to mine... Sadly, your man's phone mount is not mine.
An other idea in place of the string, Heat-shrink tubing... Replywaddra promoted this commentfreedomweasel approved this comment
I was using a binder clip attached to a fold out cupholder to mount my Zune for song choices while driving.This is a much better way to do it. Awesome. Reply
Mazda 3?Pretty clever idea, though as a few others have said I think using plastidip or something similar in place of the string would improve it.
That said, while this makes a nice travel mount, I'd spend the couple bucks on something more solid for my daily driver. Reply
Edited by freedomweasel at 01/31/11 1:38 PM
I really see no point to making your own when you can buy universal cradles for $6 at Wal-mart. Replyfreedomweasel promoted this comment
That's actually pretty clever. I've got Arkon gripper mounts with hard-mounted attachment points on the dash but this would be a nice thing to throw together for a rental car or something. And for bigger phones, just make two and put them side by side to provide four contact points on the phone.One other thing...if you're mounting to the vent like that, you'll be able to keep the phone cool in summer even if the sun's beating down. That's why I gave up on the windshield mount after one week; I got overheating warnings twice in a few days' time. Reply
Interesting timing as we just talked about this in the Honda Element Owners forum.. ideas were 3m adhesive strips and honda branded magnets:[www.elementownersclub.com] Reply
Ben R promoted this comment
<div class="noscriptbar"> In order to view comments on lifehacker.com you need to enable JavaScript.<br /> If you are using Firefox and NoScript addon, please mark lifehacker.com as trusted. </div>
Monday, January 31, 2011
How to Build a Car Mount for Your Cellphone from Office Supplies
via lifehacker.com
Open a Locked Suitcase without Leaving a Trace [Video]
Whether you've lost the key to your own suitcase and need to get it open in a hurry or you're trying to plant some contraband in your dodgy roommate's bag, this clever hack has to be seen to be believed.
Watch the video above to see how a pen can be turned into a suitcase cracking tool. In the demonstration they use a ballpoint pen to exert pressure on the zipper of a suitcase. The pressure causes the teeth to separate, effectively opening the suitcase.
The secret sauce in this hack of dubious ethics, however, isn't the pen (you could always slice a suitcase open with a knife if you wanted in that badly after all) but in the zipper mechanism itself. Zippers are self healing and if you run the zipper pull (still securely locked to the other pull, we might add) along the zipper track you'll reseal the suitcase as though you were never there.
Break Into and Reseal a Locked Suitcase [YouTube]Send an email to Jason Fitzpatrick, the author of this post, at jason@lifehacker.com.
Your version of Internet Explorer is not supported. Please upgrade to the most recent version in order to view comments.
Loading comments ...In order to view comments on lifehacker.com you need to enable JavaScript.
If you are using Firefox and NoScript addon, please mark lifehacker.com as trusted.
Whether you've lost the key to your own suitcase and need to get it open in a hurry or you're trying to plant some contraband in your dodgy roommate's bag, this clever hack has to be seen to be believed.via lifehacker.com
Subscribe to:
Posts (Atom)
Posts
